all
  • all
  • product
  • blog
  1. products
  2. Home
  3. Products
  4. PROJECTS
  5. Solutions
  6. Service
  7. About
  8. Blog
    all
    • all
    • product
    • blog
Details
  • HC1700-1.jpg
  • HC1700-3.jpg
  • HC1700-4.jpg
  • Qinzhou-2 sets HC1700 (1).jpg
  • Qinzhou-2 sets HC1700 (2).jpg
  • HC1700-1.jpg
  • HC1700-3.jpg
  • HC1700-4.jpg
  • Qinzhou-2 sets HC1700 (1).jpg
  • Qinzhou-2 sets HC1700 (2).jpg
CHINA COAL GRINDER SUPPLIERS GRINGDING MILL FINENESS ANALYSIS

Guilin Hongcheng has a complete set of efficient and environmentally friendly pulverized coal production line equipment, which can improve the comprehensive utilization rate of pulverized coal.

chat online inquiry pdf
  • Details
  • Parameters
  • Case
  • Maintenance
  • Inquiry

INTRODUCTION OF PRODUCT                                                                                                                                                                                                                        


Coal is a solid combustible mineral formed by ancient plants buried underground and undergoing complex biochemical and physical chemical changes. At present and for a long time in the future, coal is still one of the indispensable energy sources for our human production and life. For the grinding of coal, it is mainly based on the Hash grindability coefficient. The larger the Hake grindability coefficient, the better the grinding (≥65), and the smaller the Harco grindability coefficient, the more difficult it is to grind (55-60). 200 mesh, D80-D90, Raymond HC1700 and HC2000 large pendulum mills achieve low input and high output production.

 

As long as the selection of the mill is based on the output and its fineness requirements, different types of hosts are selected. The fineness of the finished product of the China coal grinder is between 200 mesh and 325 mesh. The HC coal grinding mill is a technical update based on the R-type mill. The technical indicators of this product have been greatly improved compared with the R-type mill. It is a new type of high-efficiency and energy-saving mill product. The fineness of the finished product can be adjusted arbitrarily between 22-180μm (80-600 mesh). This product is an updated product of the R-type mill. Among them, the HC1700 large vertical pendulum mill is a large Raymond mill successfully developed early in China. The output is about 2.5 to 4 times higher than that of similar 5R equipment, which effectively increases the unit output of a single device and reduces the unit. Output and energy consumption are ideal for large-scale milling projects.

 

Coal mill fineness analysis

Finished product size: 22-180μm

Production capacity: 1-25t/h

coal usage.jpg                    


ADVANTAGES AND FEATURES                                                                                                                                                                                                                       


image.png

New technology, spider-arm and pendulum grinding system. The machine has very small vibration, low noise, stable mechanical 

operation and reliable performance.





image.png

The processing capacity of materials is larger and the efficiency is 

higher. Under the condition that the total power of the R-type mill is 

unchanged, the output is increased by more than 40% year-on-year, 

and the unit power consumption cost is saved by more than 30%.








image.pngThe remaining air outlet of the mill is equipped with a pulse dust 

collector, and its dust collection efficiency reaches 99.9%. All the 

positive pressure parts of the main machine are sealed, and a 

dust-free processing workshop is basically realized.




image.pngAdopting a new sealing structure design, the grinding roller device 

can be filled with grease once in 300-500 hours. In addition, there is 

no need to remove the grinding roller device to replace the grinding 

ring, which is more convenient for maintenance.




MILL STRUCTURE & WORKING PRINCIPLE                                                                                                                                                                                                   


HC1700 coal mill consists of base, center shaft support, grinding ring, spider-arm, roller assembly, center shaft, lifter support, lifter support base, housing and other structures.


HC1700_Grinding_Structure.jpg



WORKING PRINCIPLE

Material is broken by jaw crusher firstly into required size, which are carried by bucket elevator up to storage hopper, again by feeder quantitative into host cavity for grinding, host cavity support in the plum flower rack roller device rotation around the center axis, roller under the action of centrifugal force, horizontal swing outward, so that the roller compaction of ring, roller grinding roller rotation around at the same time.


HC mill structure.jpg



COAL POWDER PRODUCTION PROCESS                                                                                                                                                                                


1. Crushing of raw materials

Large pieces of coal are crushed by the crusher to the fineness (15mm-50mm) that can enter the mill.

 

2. Drying and grinding

A. The crushed coal material with relatively low moisture content is sent to the storage hopper by the elevator, and then sent to the grinding chamber of the mill evenly and quantitatively by the feeder for grinding. The mill is treated with hot air to achieve drying in the mill and save drying costs.


B. For materials with high moisture content, use a dryer to dry the coal in the front part of the mill, and the dried raw materials are then milled for grinding.

 

3. Classification

The ground material is classified by the classification system, and the unqualified powder is classified by the classifier and returned to the main engine for re-grinding.

 

4.Collect finished products

The powder that meets the fineness is separated and collected by the airflow through the pipe into the dust collector. The collected product powder is sent to the finished product silo through the discharge port by the conveying device, and then is packaged by a powder tanker or an automatic baler.

coal processing flow.jpg


TECHNICAL DATA                                                                                                                                                                                                                                              


Model Roller Number

Roller Diameter

(mm)

Ring Inner 

Diameter (mm)

Ring Number        Capacity        (ton) Main Motor Power

(kw)

Blower Power

(kw)

Classifier Motor 

Power  (kw)

HC1300 4 410
1270
1 3-5
90 90 15
HC1700 5 510
1700 1 8-12
160
160 22



Note:

1. The Models above are equiped with newly designed spider-arm structure.

2. The capacity is for limestone powder, and specification is just a reference. The actual production depends on these materials being processed.


Remarks (main configuration):

① Adopt Hongcheng patented technology open circuit system for lignite and long flame coal with high volatility.

②The vertical pendulum structure adopts the sleeve structure for better effect.

③System design explosion-proof device.

④The dust collector and pipeline design try to avoid dead spots of dust accumulation.

⑤The powder conveying system recommends that customers use gas conveying, and conditionally add nitrogen conveying and nitric oxide detection systems.



SUCCESSFUL CASES                                                                                                                                                                                                                                       


HC1700-coal-200mesh D8012-14t (2).jpg

       

      GUILIN HONGCHENG 200,000 TON/YEAR PULVERIZED COAL BOILER HEATING PROJECT

 

      

      The model and number of this equipment: 3 HC1700 open-circuit system mills

      Processing material: Anthracite

      Fineness of finished product: 200 mesh D92

      Equipment output: 8-12 t/h






OTHER RELATED GRINDING MILL RECOMMENDATIONS                                                                                                                                                                            

             HC1700-white marble-400mesh-7.5T.jpg                     HC1700-BENTONITE-280MESH-9.5T (1).jpg                 HCH780-TALC (1).jpg

        WORKING PRINCIPLE OF PENDULUM GRINDING MACHINE-        CLAY RAYMOND MILL INDUSTRIAL DASEMENT BENTONITE FOR           SUPER FINE TALC ENERGY EFFICIENT NONMETALLIC

         RAYMOND MILL FOR SALE                                                                RECYCLED MACHINE OIL SUPPLIERS                                                         GRINDING MILL MANUFACTURING PRICE 

      

         


contact us
Submit
Related Products